Brick Paver Installation & Edging



Staging of material

Many paver jobs will vary depending on access, website conditions, task size and obviously, the weather. These situations can have an overall influence on your job from a timing stand point. Cautious consideration should be required to figure out the time to begin the paver installation. Always try to minimize or prevent any traffic on the prepared areas.

The supervisor or project supervisor must always have the materials (sand/ pavers) dispersed around the job site for simple and effective setups. Paver pallets/bundles ought to be placed in a manner not to hinder the paver installation. The correct pallet/bundle placement can make the real job installation easier and quicker by reducing the total labor of dealing with the material.

Brick paver patterns

Pavers can be positioned in various patterns depending on their shape. Each paver shape will normally have a number of different hatch patterns that are supplied by the producer.

Professionals need to take into factor to consider the traffic weight loads on their paver projects. In the majority of applications worldwide, it has actually been shown that pavers laid in a herringbone pattern have actually carried out adequately.

Pavers that are 60 mm (2 - 3/8 in) density are suitable for pedestrian applications. Pavers that are going to be utilized in commercial or commercial applications need to be 80 mm (3 - 1/8 in) in thickness.

Reference/starting point for brick paver installation

There are a variety of conditions that identify the beginning point of a paver task.

When starting to set up pavers it is best to snap a true straight chalk line on the surface of the bed linen sand or pull a true straight string line above the surface area of the bedding sand at the ended up elevation of the pavers This will help as a guide for keeping straight joint lines and will also permit the installer to make adjustments in the positioning of the pavers.

Buildings and concrete suppressing are generally not straight and must not be utilized for establishing straight joint lines. The usage of string lines is essential to identify the real straightness of the edge. As the paver installation progresses, the string lines will assist lessen the need for small trim pieces.

These will keep a minimum joint width and allow the bed linen and jointing sand to get in in between each paver. Pavers with spacer bars are typically not laid in snug against each other considering that a string line will supply consistent joint spacing.

Installation of brick pavers.

One of the most widely used techniques for the installation of pavers is hand installation of each paver. It is best to set up a single row of pavers along one of the true straight lines that you have pulled or above the bedding sand. The best technique is to position a paver against another one and let it slide down into the bed linen sand.

When setting up pavers on a steep grade, they ought to be set up at the base of the grade going uphill. This will avoid the pavers from creeping as they are being laid.

On large industrial and commercial applications, hand laying pavers would not be cost effective due to the labor strength. The best way for installing pavers on big jobs is to install them mechanically. Making use of a mechanical laying maker can install roughly 6000 - 7000 sq ft a day. There are a couple products a specialist should consider before setting up pavers mechanically:

1.) Mechanical installers are just capable of installing pavers in certain patterns.

2.) The professional should make certain that the maker can manufacturing and bundling pavers in the desired pattern on the pallets for easy mechanical installation.

3.) Contractors may experience a color mixing scenario coming off the packages of pavers Poor color mixing might result in a patchy looking installation. Many producers are consistent with color blending on each bundle of pavers, but it is the professional's obligation to guarantee appropriate mixing in the field.

Cutting procedures for brick pavers.

Professionals generally have two ways of cutting pavers. Pavers are cut either by 1). A double bladed guillotine or by 2). A gas powered cut off saw or brick saw which is equipped with a diamond blade. The diamond blade cut-off saw or brick saw will offer a much cleaner and more accurate cut. Many brick saws will have a hose pipe attachment on them which will enable the operator to cut the pavers damp. When cutting pavers damp, it will assist decrease dust and will lengthen the diamond blades life. The operator of the brick saw need to constantly cut the pavers far from the surface area of the paver field when cutting wet, due to the fact that the pavers will create a slurry that will stain the paver surface. Pavers that are cut should not fit tight, adequate spacing must be available for jointing sand.

The brick saw operator needs to constantly use the appropriate security that is needed for operating a saw, such as eye, ear, breathing and hand defense ).

Edging types

Edge restraints play a significant role in the overall success of an interlocking pavement installation Edging restraints eliminate lateral motion of the pavers and hold the pavers securely together. Specifically at the external boundary of the paver application, without an edging restraint, your project is guaranteed to stop working gradually.

Normally made edge restraints are the most frequently used by specialists. Made edging restraints can vary from, plastic edging, steel and aluminum, lumbers or precast concrete and stone.

Edging installation.

This could result in the migration of the bedding sand and ultimate lateral South Florida Pavers movement of the pavers. If there is a possibility of losing bed linen sand between the pavers and the edge restraint, then geo textile material is suggested. When a gap in between the pavers and the edging exceeds 3/8" (10mm), then the area ought to be filled with cut pavers.

Compaction of brick pavers.

After installation, the pavers have to be compacted. The whole area that is to be compressed must be swept clean of any foreign items and particles that can cause scuffing or scratching on the surface of the pavers.

It is essential to have a compactor that can apply between 3000lbs. And 5000 pounds. Of centrifugal compaction force. In addition, it is very important that the first compaction occurs before any jointing sand has been applied to the pavers. This can cause a bridging issue and will not allow the joints to be totally filled with jointing sand if jointing sand is used to the pavers before compaction takes location. This can also avoid the pavers from being properly set into the bed linen sand.

When condensing the pavers, it is advised that you make at least 2 passes in different directions throughout the pavers. This will allow the pavers to be appropriately set in the bedding sand and will require the bedding sand up into the joints from the bottom of the pavers.

The compaction of the pavers is extremely important to the final efficiency of the pavers. Failure to do proper compaction can result in deformations and pavement failure gradually.


Paver pallets/bundles should be put in a way not to interfere with the paver installation. One of the most widely used approaches for the installation of pavers is hand installation of each paver. The operator of the brick saw should always cut the pavers away from the surface area of the paver field when cutting damp, due to the fact that the pavers will produce a slurry that will stain the paver surface area. Edging restraints eliminate lateral motion of the pavers and hold the pavers securely together. When a gap between the pavers and the edging goes beyond 3/8" (10mm), then the space ought to be filled with cut pavers.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments on “Brick Paver Installation & Edging”

Leave a Reply

Gravatar